View WM8759_51844.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

w
DESCRIPTION
The WM8759 is a high performance stereo DAC with an integrated headphone driver. It is designed for audio applications such as portable DVD, MP3 players or consumer equipment with line output and headphone output connections. The WM8759 supports data input word lengths from 16 to 24-bits and sampling rates up to 192kHz. The WM8759 consists of a serial interface port, digital interpolation filters, multi-bit sigma delta modulators and stereo DAC in a 14-pin SOIC package. The hardware control interface is used for the selection of audio data interface format, enable and de-emphasis. The WM8759 supports I2S, right Justified or DSP interfaces. Operating on split analog digital supplies the WM8759 allows very lower power consumption from the digital section, whilst supporting large output powers from the analog headphone driver.
WM8759
24-bit 192kHz Stereo DAC with Headphone Buffer
FEATURES
* * * Stereo DAC with headphone driver 50mW power into 16R load on 3.3V supply Audio Performance * * * * * 100dB SNR (`A' weighted @ 48kHz) -88dB THD line level
-72dB THD headphone DAC Sampling Frequency: 8kHz - 192kHz Pin Selectable Audio Data Interface Format I2S, 16-bit Right Justified or DSP 2.7V - 5.5V Supply Operation, Split Analog-digital supplies 14-pin SOIC Package Typical power consumption 20mW on 2.7V supply
APPLICATIONS
* * * Portable music Players Home music players Digital TV
BLOCK DIAGRAM
WOLFSON MICROELECTRONICS plc www.wolfsonmicro.com
Advanced Information, September 2004, Rev 3.0
Copyright 2004 Wolfson Microelectronics plc
WM8759
Advanced Information
TABLE OF CONTENTS DESCRIPTION ............................................................................................................1 FEATURES..................................................................................................................1 APPLICATIONS ..........................................................................................................1 BLOCK DIAGRAM ......................................................................................................1 TABLE OF CONTENTS ..............................................................................................2 PIN CONFIGURATION................................................................................................3 ORDERING INFORMATION .......................................................................................3 PIN DESCRIPTION .....................................................................................................4 ABSOLUTE MAXIMUM RATINGS..............................................................................5 DC ELECTRICAL CHARACTERISTICS .....................................................................6 ELECTRICAL CHARACTERISTICS ...........................................................................6
MASTER CLOCK TIMING .................................................................................................. 8 DIGITAL AUDIO INTERFACE ............................................................................................ 8
DEVICE DESCRIPTION..............................................................................................9
GENERAL INTRODUCTION .............................................................................................. 9 DAC CIRCUIT DESCRIPTION ........................................................................................... 9 CLOCKING SCHEMES .....................................................................................................10 DIGITAL AUDIO INTERFACE ...........................................................................................10 AUDIO DATA SAMPLING RATES.....................................................................................12 HARDWARE CONTROL MODES .....................................................................................13 DIGITAL FILTER CHARACTERISTICS.............................................................................14 DAC FILTER RESPONSES...............................................................................................14
DIGITAL DE-EMPHASIS CHARACTERISTICS ........................................................15 APPLICATIONS INFORMATION ..............................................................................16 RECOMMENDED EXTERNAL COMPONENTS .......................................................16
POWER UP/DOWN SEQUENCE......................................................................................16 PCB LAYOUT RECOMMENDATIONS ..............................................................................17
PACKAGE DRAWING...............................................................................................18 IMPORTANT NOTICE ...............................................................................................19
ADDRESS: ........................................................................................................................19
w
AI Rev 3.0 September 2004 2
Advanced Information
WM8759
PIN CONFIGURATION
ORDERING INFORMATION
DEVICE WM8759ED/V WM8759ED/RV WM8759GED/V TEMPERATURE RANGE -25 to +85oC -25 to +85 C -25 to +85oC
o
PACKAGE 14-pin SOIC 14-pin SOIC (tape and reel) 14-pin SOIC (lead free) 14-pin SOIC (lead free, tape and reel)
MOISTURE SENSITIVITY LEVEL MSL2 MSL2 MSL2
PEAK SOLDERING TEMPERATURE 240C 240C 260C
WM8759GED/RV
-25 to +85oC
MSL2
260C
Note: Reel quantity = 3,000
w
AI Rev 3.0 September 2004 3
WM8759
Advanced Information
PIN DESCRIPTION
PIN 1 2 3 4 5 6 7 8 9 10 11 12 NAME LRCIN DIN BCKIN ENABLE CAP HPOUTR AGND AVDD HPOUTL DGND DVDD DEEMPH TYPE Digital input Digital input Digital input Digital input Analogue output Analogue output Supply Supply Analogue output Digital Supply Digital Supply Digital input Sample rate clock input Serial audio data input Bit clock input Enable input - 0 = powered down, 1 = enabled Analogue internal reference Right channel DAC output Ground reference for analog circuits and substrate connection Positive supply for analog circuits Left channel DAC output Digital ground supply Digital positive supply De-emphasis select, Internal pull down High = de-emphasis ON Low = de-emphasis OFF Data input format select, Internal pull up Low = 16-bit right justified or DSP `late' High = 16-24-bit I2S or DSP `early' Master clock input DESCRIPTION
13
FORMAT
Digital input
14
MCLK
Digital input
Note: 1. Digital input pins have Schmitt trigger input buffers.
w
AI Rev 3.0 September 2004 4
Advanced Information
WM8759
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified. ESD Sensitive Device. This device is manufactured on a CMOS process. It is therefore generically susceptible to damage from excessive static voltages. Proper ESD precautions must be taken during handling and storage of this device. Wolfson tests its package types according to IPC/JEDEC J-STD-020B for Moisture Sensitivity to determine acceptable storage conditions prior to surface mount assembly. These levels are: MSL1 = unlimited floor life at <30C / 85% Relative Humidity. Not normally stored in moisture barrier bag. MSL2 = out of bag storage for 1 year at <30C / 60% Relative Humidity. Supplied in moisture barrier bag. MSL3 = out of bag storage for 168 hours at <30C / 60% Relative Humidity. Supplied in moisture barrier bag. The Moisture Sensitivity Level for each package type is specified in Ordering Information. CONDITION Supply voltage Voltage range digital inputs Master Clock Frequency Operating temperature range, TA Storage temperature prior to soldering Storage temperature after soldering -25C MIN -0.3V GND -0.3V MAX +7V VDD +0.3V 50MHz +85C
30C max / 85% RH max -65C +150C
w
AI Rev 3.0 September 2004 5
WM8759
Advanced Information
DC ELECTRICAL CHARACTERISTICS
PARAMETER Supply range Ground Analog supply current Digital supply current Power down current (note 4) SYMBOL AVDD, DVDD AGND, DGND AVDD = 5V AVDD = 3.3V DVDD = 5V DVDD = 3.3V AVDD=DVDD=5V 8 4 0.01 mA mA TEST CONDITIONS MIN 2.7 0 12 TYP MAX 5.5 UNIT V V mA
ELECTRICAL CHARACTERISTICS
Test Conditions o AVDD = 5V, DVDD = 3.3V, GND = 0V, TA = +25 C, fs = 48kHz, MCLK = 256fs unless otherwise stated. PARAMETER Digital Logic Levels (TTL Levels) Input LOW level Input HIGH level Output LOW Output HIGH Analogue Reference Levels Reference voltage (CAP) Potential divider resistance DAC Output (Load = 10k. 50pF) 0dBFs Full scale output voltage SNR (Note 5,6,7) SNR (Note 5,6,7) SNR (Note 5,6,7) SNR (Note 5,6,7) At DAC outputs A-weighted, @ fs = 48kHz A-weighted @ fs = 96kHz A-weighted @ fs = 192kHz A-weighted, @ fs = 48kHz VDD = 3.3V A-weighted @ fs = 96kHz VDD = 3.3V Non `A' weighted @ fs = 48kHz 1kHz, 0dBFs 1kHz, 0dBFs 94 1.1 x AVDD/5 100 97 97 95 Vrms dB dB dB dB RCAP AVDD to CAP and CAP to GND AVDD/2 50k V VIL VIH VOL VOH IOL = 2mA IOH = 2mA DVDD - 0.3V 2.0 DGND + 0.3V 0.8 V V V V SYMBOL TEST CONDITIONS MIN TYP MAX UNIT
SNR (Note 5,6,7)
95
dB
SNR (Note 5,6,7) THD+N (Note 7) THD+N driving headphone DAC channel separation 10k load 16R load
97 -88 -72 93
dB dB dB dB
w
AI Rev 3.0 September 2004 6
Advanced Information Test Conditions AVDD = 5V, DVDD = 3.3V, GND = 0V, TA = +25oC, fs = 48kHz, MCLK = 256fs unless otherwise stated. PARAMETER Analogue Output Levels Output level Load = 10k, 0dBFS Load = 10k, 0dBFS, (AVDD = 3.3V) 1.1 0.72 1 To midrail or a.c. coupled To midrail or a.c. coupled (AVDD = 3.3V) 16 16 SYMBOL TEST CONDITIONS MIN TYP MAX
WM8759
UNIT Vrms Vrms %FSR
Gain mismatch channel-to-channel Minimum resistance load
Output d.c. level
AVDD/2
V
Notes: 1. Ratio of output level with 1kHz full scale input, to the output level with all zeros into the digital input, measured `A' weighted over a 20Hz to 20kHz bandwidth. 2. All performance measurements done with 20kHz low pass filter, and where noted an A-weight filter. Failure to use such a filter will result in higher THD+N and lower SNR and Dynamic Range readings than are found in the Electrical Characteristics. The low pass filter removes out of band noise; although it is not audible it may affect dynamic specification values. 3. CAP pin decoupled with 10uF and 0.1uF capacitors (smaller values may result in reduced performance). 4. Power down occurs 1.5s after MCLK is stopped. 5. 6. Signal-to-noise ratio (dB) - SNR is a measure of the difference in level between the full scale output and the output with no signal applied. (No Auto-zero or Automute function is employed in achieving these results). Dynamic range (dB) - DNR is a measure of the difference between the highest and lowest portions of a signal. Normally a THD+N measurement at 60dB below full scale. The measured signal is then corrected by adding the 60dB to it. (e.g. THD+N @ -60dB= -32dB, DR= 92dB). THD+N (dB) - THD+N is a ratio, of the rms values, of (Noise + Distortion)/Signal. Stop band attenuation (dB) - Is the degree to which the frequency spectrum is attenuated (outside audio band). Channel Separation (dB) - Also known as Cross-Talk. This is a measure of the amount one channel is isolated from the other. Normally measured by sending a full scale signal down one channel and measuring the other.
7. 8. 9.
w
AI Rev 3.0 September 2004 7
WM8759 MASTER CLOCK TIMING
tMCLKL MCLK tMCLKH tMCLKY
Advanced Information
Figure 1 Master Clock Timing Requirements Test Conditions VDD = 5V, GND = 0V, TA = +25oC, fs = 48kHz, MCLK = 256fs unless otherwise stated. PARAMETER System Clock Timing Information
MCLK Master clock pulse width high MCLK Master clock pulse width low MCLK Master clock cycle time MCLK Duty cycle Time from MCLK stopping to power down.
SYMBOL tMCLKH tMCLKL tMCLKY
TEST CONDITIONS
MIN 8 8 20 40:60 1.5
TYP
MAX
UNIT ns ns ns
60:40 12 s
DIGITAL AUDIO INTERFACE
tBCH BCKIN tBCY tBCL
LRCIN tDS DIN tDH tLRH tLRSU
Figure 2 Digital Audio Data Timing Test Conditions VDD = 5V, GND = 0V, TA = +25oC, fs = 48kHz, MCLK = 256fs unless otherwise stated. PARAMETER BCKIN cycle time BCKIN pulse width high BCKIN pulse width low LRCIN set-up time to BCKIN rising edge LRCIN hold time from BCKIN rising edge DIN set-up time to BCKIN rising edge DIN hold time from BCKIN rising edge SYMBOL tBCY tBCH tBCL tLRSU tLRH tDS tDH TEST CONDITIONS MIN 40 16 16 8 8 8 8 TYP MAX UNIT ns ns ns ns ns ns ns
Audio Data Input Timing Information
w
AI Rev 3.0 September 2004 8
Advanced Information
WM8759
DEVICE DESCRIPTION
GENERAL INTRODUCTION
The WM8759 is a high performance DAC with integrated headphone output buffer, designed for digital consumer audio applications. The range of features make it ideally suited for use in portable DVD players, MP3 players and other consumer audio equipment. The WM8759 is a complete 2-channel stereo audio digital-to-analogue converter, including digital interpolation filter, multi-bit sigma delta with dither, and switched capacitor multi-bit stereo DAC and output smoothing filters. It is fully compatible and an ideal partner for a range of industry standard microprocessors, controllers and DSPs. A novel multi bit sigma-delta DAC design is used, utilising a 128x oversampling rate, to optimise signal to noise performance and offer increased clock jitter tolerance. (In `high-rate' operation, the oversampling ratio is 64x for system clocks of 128fs or 192fs) Control of the internal functionality of the device is provided by hardware control (pin programmed). Operation using master clocks of 256fs, 384fs, 512fs or 768fs is provided, selection between clock rates being automatically controlled. Sample rates (fs) from less than 8kHz to 96kHz are allowed, provided the appropriate system clock is input. Support is also provided for up to 192kHz using a master clock of 128fs or 192fs. The audio data interface supports 16-bit right justified or 16-24-bit I2S (Philips left justified, one bit delayed) interface formats. A DSP interface is also supported, enhancing the interface options for the user. Split analog and digital 2.7-5.5V supply may be used, the output amplitude scaling with absolute analog supply level. Low supply voltage operation and low current consumption combined with the low pin count small package make the WM8759 attractive for many consumer applications. A power down mode is provided, allowing power consumption to be minimised. The device is packaged in a small 14-pin SOIC.
DAC CIRCUIT DESCRIPTION
The WM8759 DAC is designed to allow playback of 24-bit PCM audio or similar data with high resolution and low noise and distortion. Sample rates up to 192kHz may be used, with much lower sample rates being acceptable provided that the ratio of sample rate (LRCIN) to master clock (MCLK) is maintained at one of the required rates. The two DACs on the WM8759 are implemented using sigma-delta oversampled conversion techniques. These require that the PCM samples are digitally filtered and interpolated to generate a set of samples at a much higher rate than the up to 192kHz input rate. This sample stream is then digitally modulated to generate a digital pulse stream that is then converted to analogue signals in a switched capacitor DAC. The advantage of this technique is that the DAC is linearised using noise shaping techniques, allowing the 24-bit resolution to be met using non-critical analogue components. A further advantage is that the high sample rate at the DAC output means that smoothing filters on the output of the DAC need only have fairly crude characteristics in order to remove the characteristic steps, or images on the output of the DAC. To prevent the generation of unwanted tones dithering is used in the digital modulator along with a higher order modulator. The multi-bit switched capacitor technique used in the DAC reduces sensitivity to clock jitter, and dramatically reduces out of band noise compared to switched current or single bit techniques used in other implementations. The voltage on the CAP pin is used as the reference for the DACs. Therefore the amplitude of the signals at the DAC outputs will scale with the amplitude of the voltage at the CAP pin. An external reference could be used to drive into the CAP pin if desired, with a value typically of about midrail ideal for optimum performance.
w
AI Rev 3.0 September 2004 9
WM8759
Advanced Information The outputs of the 2 DACs are buffered out of the device by buffer amplifiers capable of driving loads of either line level or headphone level impedance. The advanced multi-bit DAC used in WM8759 produces far less out of band noise than single bit traditional sigma delta DACs, and so in most applications where line level output is required, no post DAC filter is required. Typically an AC coupling capacitor and a DC setting resistor to ground are the only components required on the output of the chip.
CLOCKING SCHEMES
In a typical digital audio system there is only one central clock source producing a reference clock to which all audio data processing is synchronised. This clock is often referred to as the audio system's Master Clock. The external master clock can be applied directly through the MCLK input pin with no configuration necessary for sample rate selection. Note that on the WM8759, MCLK is used to derive clocks for the DAC path. The DAC path consists of DAC sampling clock, DAC digital filter clock and DAC digital audio interface timing. In a system where there are a number of possible sources for the reference clock it is recommended that the clock source with the lowest jitter be used to optimise the performance of the DAC. The device can be powered down by stopping MCLK. In this state the power consumption is substantially reduced.
DIGITAL AUDIO INTERFACE
Audio data is applied to the internal DAC filters via the Digital Audio Interface. Three interface formats are supported: * * * Right Justified mode I S mode DSP mode
2
All formats send the MSB first. The data format is selected with the FORMAT pin. When FORMAT is LOW, right justified data format is selected and word lengths of 16-bits may be used. When the FORMAT pin is HIGH, I2S format is selected and word length of any value up to 24-bits may be used. (If a word length shorter than 24-bits is used, the unused bits should be padded with zeros). If LRCIN is 4 BCKINs or less duration, the DSP compatible format is selected. Early and Late clock formats are supported, selected by the state of the FORMAT pin. `Packed' mode (i.e. only 32 or 48 clocks per LRCIN period) operation is also supported in both I S (16-24 bits) and right justified formats, (16 bit). If a `packed' format of 16-bit word length is applied (16 BCKINS per LRCIN half period), the device auto-detects this mode and switches to 16-bit data length.
2
I S MODE
The WM8759 supports word lengths of 16-24 bits in I2S mode. In I2S mode, the digital audio interface receives data on the DIN input. Audio Data is time multiplexed with LRCIN indicating whether the left or right channel is present. LRCIN is also used as a timing reference to indicate the beginning or end of the data words. In I2S modes, the minimum number of BCKINs per LRCIN period is 2 times the selected word length. LRCIN must be high for a minimum of word length BCKINs and low for a minimum of word length BCKINs. Any mark to space ratio on LRCIN is acceptable provided the above requirements are met. In I2S mode, the MSB is sampled on the second rising edge of BCKIN following a LRCIN transition. LRCIN is low during the left samples and high during the right samples.
2
w
AI Rev 3.0 September 2004 10
Advanced Information
WM8759
1/fs
LEFT CHANNEL LRCIN
RIGHT CHANNEL
BCKIN
1 BCKIN 1 BCKIN 3 n-2 n-1 n 1 2 3 n-2 n-1 n
DIN
1
2
MSB
LSB
MSB
LSB
Figure 3 I2S Mode Timing Diagram
RIGHT JUSTIFIED MODE
The WM8759 supports word lengths of 16-bits in right justified mode. In right justified mode, the digital audio interface receives data on the DIN input. Audio Data is time multiplexed with LRCIN indicating whether the left or right channel is present. LRCIN is also used as a timing reference to indicate the beginning or end of the data words. In right justified mode, the minimum number of BCKINs per LRCIN period is 2 times the selected word length. LRCIN must be high for a minimum of word length BCKINs and low for a minimum of word length BCKINs. Any mark to space ratio on LRCIN is acceptable provided the above requirements are met. In right justified mode, the LSB is sampled on the rising edge of BCKIN preceding a LRCIN transition. LRCIN is high during the left samples and low during the right samples.
1/fs
LEFT CHANNEL LRCIN
RIGHT CHANNEL
BCKIN
DIN
1
2
3
14
15
16
1
2
3
14
15
16
MSB
LSB
MSB
LSB
Figure 4 Right Justified Mode Timing Diagram
DSP MODE
A DSP compatible, time division multiplexed format is also supported by the WM8759. This format is of the type where a `synch' pulse is followed by two data words (left and right) of predetermined word length. (16-bits). The `synch' pulse replaces the normal duration LRCIN, and DSP mode is auto-detected by the shorter than normal duration of the LRCIN. If LRCIN is of 4 BCKIN or less duration, the DSP compatible format is selected. Early and Late clock formats are supported, selected by the state of the FORMAT pin.
w
AI Rev 3.0 September 2004 11
WM8759
1/fs
Advanced Information
Max 4 BCKIN's LRCIN
BCKIN
LEFT CHANNEL DIN
1 2 1
RIGHT CHANNEL
2
NO VALID DATA
1
15
16
15
16
MSB
Input Word Length (16 bits)
LSB
Figure 5 DSP `Late' Mode Timing
1 BCKIN 1/fs 1 BCKIN
max 4 BCKIN's LRCIN
BCKIN
LEFT CHANNEL DIN
1 2 1
RIGHT CHANNEL
2
NO VALID DATA
16
15
16
15
MSB
Input Word Length (16 bits)
LSB
Figure 6 DSP `Early' Mode Timing
AUDIO DATA SAMPLING RATES
The master clock for WM8759 supports audio sampling rates from 128fs to 768fs, where fs is the audio sampling frequency (LRCIN) typically 32kHz, 44.1kHz, 48kHz, 96kHz or 192kHz. The master clock is used to operate the digital filters and the noise shaping circuits. The WM8759 has a master clock detection circuit that automatically determines the relation between the master clock frequency and the sampling rate (to within +/- 8 master clocks). If there is a greater than 8 clocks error, the interface shuts down the DAC and mutes the output. The master clock should be synchronised with LRCIN, although the WM8759 is tolerant of phase differences or jitter on this clock. SAMPLING RATE (LRCIN) 32kHz 44.1kHz 48kHz 96kHz 192kHz MASTER CLOCK FREQUENCY (MHZ) (MCLK) 128fs 4.096 5.6448 6.144 12.288 24.576 192fs 6.144 8.467 9.216 18.432 36.864 256fs 8.192 11.2896 12.288 24.576 Unavailable 384fs 12.288 16.9344 18.432 36.864 Unavailable 512fs 16.384 22.5792 24.576 Unavailable Unavailable 768fs 24.576 33.8688 36.864 Unavailable Unavailable
Table 1 Master Clock Frequencies Versus Sampling Rate
w
AI Rev 3.0 September 2004 12
Advanced Information
WM8759
HARDWARE CONTROL MODES
The WM8759 is hardware programmable providing the user with options to select input audio data format, de-emphasis and mute.
ENABLE OPERATION
Pin 4 (ENABLE) controls the operation of the chip. If ENABLE is low the device is held in a low power state. If this pin is held high the device is powered up. To ensure correct operation it is essential that there is a low to high transition on the ENABLE pin after digital supplies have come on. This can be achieved by providing the ENABLE signal from an external controller chip or by means of a simple RC network on the ENABLE pin. See "Recommended External Components" in the "Application Information" section at the end of this datasheet. Note that the ENABLE pin should not be used as a mute pin or to temporarily silence the DAC (between tracks of a CD for example). The ENABLE pin is not intended to be used as a mute control but to allow entry into low power mode. Disabling the device via the ENABLE pin has the effect of powering down the voltage on the CAP pin. Repeated enabling/disabling of the device can cause audible pops at the output.
HIGH PERFORMANCE MODE
On the rising edge of ENABLE, the DEEMPH pin is sampled. If it is low the device powers up normally. If it is high the device goes into a high performance and high power consumption state. Once ENABLE is high, DEEMPH controls the selection of the de-emphasis filter.
INPUT AUDIO FORMAT SELECTION
FORMAT (pin 13) controls the data input format. FORMAT 0 1 Table 2 Input Audio Format Selection Notes: 1. In 16-24 bit I2S mode, any data from 16-24 bits or more is supported provided that LRCIN is high for a minimum of data width BCKINs and low for a minimum of data width BCKINs, unless Note 2. For data widths greater than 24 bits, the LSB's will be truncated and the most significant 24 bits will be used by the internal processing. If exactly 16 BCKIN cycles occur in both the low and high period of LRCIN the WM8759 will assume the data is 16-bit and accept the data accordingly. INPUT DATA MODE 16 bit right justified 16-24 bit I2S
2.
INPUT DSP FORMAT SELECTION
FORMAT 0 1 50% LRCIN DUTY CYCLE 16 bit (MSB-first, right justified) I2S format up to 24 bit (Philips serial data protocol) LRCIN of 4 BCKIN or Less Duration DSP format - `late' mode DSP format - `early' mode
Table 3 DSP Interface Formats
DE-EMPHASIS CONTROL
DEEMPH (pin 12) is an input control for selection of de-emphasis filtering to be applied. DEEMPH 0 1 Table 4 De-emphasis Control AI Rev 3.0 September 2004 13 DE-EMPHASIS Off On
w
WM8759 DIGITAL FILTER CHARACTERISTICS
PARAMETER Passband Edge Passband Ripple Stopband Attenuation Table 5 Digital Filter Characteristics SYMBOL TEST CONDITIONS -3dB f < 0.444fs f > 0.555fs -60 MIN TYP 0.487fs
Advanced Information
MAX 0.05
UNIT dB dB
DAC FILTER RESPONSES
0.2 0 0.15 -20 0.1
Response (dB)
Response (dB)
-40
0.05 0 -0.05 -0.1
-60
-80
-100
-0.15 -0.2 0 0.5 1 1.5 Frequency (Fs) 2 2.5 3 0 0.05 0.1 0.15 0.2 0.25 0.3 Frequency (Fs) 0.35 0.4 0.45 0.5
-120
Figure 7 DAC Digital Filter Frequency Response -44.1, 48 and 96kHz
Figure 8 DAC Digital Filter Ripple -44.1, 48 and 96kHz
0.2
0 0 -20
Response (dB)
Response (dB)
-0.2
-40
-0.4
-60
-0.6
-0.8 -80 -1 0 0.2 0.4 0.6 Frequency (Fs) 0.8 1 0 0.05 0.1 0.15 0.2 0.25 0.3 Frequency (Fs) 0.35 0.4 0.45 0.5
Figure 9 DAC Digital Filter Frequency Response -192kHz
Figure 10 DAC Digital Filter Ripple -192kHz
w
AI Rev 3.0 September 2004 14
Advanced Information
WM8759
DIGITAL DE-EMPHASIS CHARACTERISTICS
0 1 0.5 -2 0
Response (dB)
-4
Response (dB)
-0.5 -1 -1.5 -2
-6
-8 -2.5 -10 0 2 4 6 8 10 Frequency (kHz) 12 14 16 -3 0 2 4 6 8 10 Frequency (kHz) 12 14 16
Figure 11 De-Emphasis Frequency Response (32kHz)
0
Figure 12 De-Emphasis Error (32kHz)
0.4 0.3
-2 0.2
Response (dB)
Response (dB)
-4
0.1 0 -0.1 -0.2
-6
-8 -0.3 -10 0 5 10 Frequency (kHz) 15 20 -0.4 0 5 10 Frequency (kHz) 15 20
Figure 13 De-Emphasis Frequency Response (44.1kHz)
0
Figure 14 De-Emphasis Error (44.1kHz)
1 0.8
-2
0.6 0.4
Response (dB)
-4
Response (dB)
0.2 0 -0.2 -0.4
-6
-8
-0.6 -0.8
-10 0 5 10 15 Frequency (kHz) 20
-1 0 5 10 15 Frequency (kHz) 20
Figure 15 De-Emphasis Frequency Response (48kHz)
Figure 16 De-Emphasis Error (48kHz)
w
AI Rev 3.0 September 2004 15
WM8759
Advanced Information
APPLICATIONS INFORMATION RECOMMENDED EXTERNAL COMPONENTS
Figure 17 External Component Diagram In an application where ENABLE is fed directly from VDD rather than a dedicated control line, resistor R3 and capacitor C9 are used on the ENABLE pin to introduce a short delay in the Low to High transition of ENABLE. This will ensure the pin goes high after power supplies have had time to settle (see "ENABLE Operation" in the "Hardware Control Modes" section of the datasheet). However, if the ENABLE signal is being provided from an external controller chip rather than VDD directly, R3 and C9 will not be required.
POWER UP/DOWN SEQUENCE
POWER UP/DOWN SEQUENCE
For click free operation, the WM8759 should be powered up and down in a specific sequence. Power-up: 1. 2. 3. Power up AVDD and DVDD and wait to settle Turn on clocks and data (MCLK, BCLK, LRCLK, SDATA) Switch ENABLE pin from low to high
Power-down: 1. 2. 3. Switch Enable from high to low Remove clocks and data Power down AVDD and DVDD
w
AI Rev 3.0 September 2004 16
Advanced Information
WM8759
PCB LAYOUT RECOMMENDATIONS
Care should be taken in the layout of the PCB that the WM8759 is to be mounted to. The following notes will help in this respect: 1. The VDD supply to the device should be as noise free as possible. This can be accomplished to a large degree with a 10uF bulk capacitor placed locally to the device and a 0.1uF high frequency decoupling capacitor placed as close to the VDD pin as possible. It is best to place the 0.1uF capacitor directly between the VDD and GND pins of the device on the same layer to minimize track inductance and thus improve device decoupling effectiveness. The CAP pin should be as noise free as possible. This pin provides the decoupling for the on chip reference circuits and thus any noise present on this pin will be directly coupled to the device outputs. In a similar manner to the VDD decoupling described above, this pin should be decoupled with a 10uF bulk capacitor local to the device and a 0.1uF capacitor as close to the CAP pin as possible. Separate analogue and digital track routing from each other. The device is split into analogue (pins 5 - 9) and digital (pins 1 - 4 and pins 10 - 14) sections that allow the routing of these signals to be easily separated. By physically separating analogue and digital signals, crosstalk from the PCB can be minimized. Use an unbroken solid GND plane. To achieve best performance from the device, it is advisable to have either a GND plane layer on a multilayer PCB or to dedicate one side of a 2 layer PCB to be a GND plane. For double sided implementations it is best to route as many signals as possible on the device mounted side of the board, with the opposite side acting as a GND plane. The use of a GND plane greatly reduces any electrical emissions from the PCB and minimizes crosstalk between signals.
2.
3.
4.
An evaluation board is available for the WM8759 that demonstrates the above techniques and the excellent performance achievable from the device. This can be ordered or the User manual downloaded from the Wolfson web site at www.wolfsonmicro.com
w
AI Rev 3.0 September 2004 17
WM8759
Advanced Information
PACKAGE DRAWING
D: 14 PIN SOIC 3.9mm Wide Body DM001.C
e
B
14
8
H E
1
7
D
L h x 45o
A1 -CA
SEATING PLANE
C
0.10 (0.004)
Symbols A A1 B C D E e H h L REF:
Dimensions (MM) MIN MAX 1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 8.55 8.75 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.27 o o 0 8 JEDEC.95, MS-012
Dimensions (Inches) MIN MAX 0.0532 0.0688 0.0040 0.0098 0.0130 0.0200 0.0075 0.0098 0.3367 0.3444 0.1497 0.1574 0.05 BSC 0.2284 0.2440 0.0099 0.0196 0.0160 0.0500 o o 0 8
NOTES: A. ALL LINEAR DIMENSIONS ARE IN MILLIMETERS (INCHES). B. THIS DRAWING IS SUBJECT TO CHANGE WITHOUT NOTICE. C. BODY DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSION, NOT TO EXCEED 0.25MM (0.010IN). D. MEETS JEDEC.95 MS-012, VARIATION = AB. REFER TO THIS SPECIFICATION FOR FURTHER DETAILS.
w
AI Rev 3.0 September 2004 18
Advanced Information
WM8759
IMPORTANT NOTICE
Wolfson Microelectronics plc (WM) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current. All products are sold subject to the WM terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability.
WM warrants performance of its products to the specifications applicable at the time of sale in accordance with WM's standard warranty. Testing and other quality control techniques are utilised to the extent WM deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements.
In order to minimise risks associated with customer applications, adequate design and operating safeguards must be used by the customer to minimise inherent or procedural hazards. Wolfson products are not authorised for use as critical components in life support devices or systems without the express written approval of an officer of the company. Life support devices or systems are devices or systems that are intended for surgical implant into the body, or support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided, can be reasonably expected to result in a significant injury to the user. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
WM assumes no liability for applications assistance or customer product design. WM does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of WM covering or relating to any combination, machine, or process in which such products or services might be or are used. WM's publication of information regarding any third party's products or services does not constitute WM's approval, license, warranty or endorsement thereof.
Reproduction of information from the WM web site or datasheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations and notices. Representation or reproduction of this information with alteration voids all warranties provided for an associated WM product or service, is an unfair and deceptive business practice, and WM is not responsible nor liable for any such use.
Resale of WM's products or services with statements different from or beyond the parameters stated by WM for that product or service voids all express and any implied warranties for the associated WM product or service, is an unfair and deceptive business practice, and WM is not responsible nor liable for any such use.
ADDRESS:
Wolfson Microelectronics plc Westfield House 26 Westfield Road Edinburgh EH11 2QB United Kingdom
Tel :: +44 (0)131 272 7000 Fax :: +44 (0)131 272 7001 Email :: sales@wolfsonmicro.com
w
AI Rev 3.0 September 2004 19

▲Up To Search▲

Price & Availability of WM8759

	To Download WM8759 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .